         SweepGen - An Audio Sweep Generator - David J Taylor


SweepGen turns a PC into an Audio Oscillator and Sweep Generator which can be
used for testing audio or educational purposes.  In conjunction with audio
test instruments, you can make frequency response plots.  SweepGen uses the
sound card in your PC to produce sinewaves that are mathematically correct
almost to CD quality, indeed it's more likely that the quality of your PC
sound card will be the limiting factor rather than the code in SweepGen.


Installation & Usage:

Extract SweepGen.exe from the Zip file to a suitable location, and run it!

SweepGen will save the current settings in the registry each time a sweep
is started, thus allowing you to save personalised settings.


Support Policy:

This program is currently freeware, but you must register for any support.
As an incentive to register, you will be able to save the wave file produced
by the program in the registered version.  Use the Help, Register menu to
enter the registration details you will get from me.  You can register the
Audio Tools here:

  http://www.satsignal.eu/software/reg-audio-tools.html


Operating modes:

SweepGen has six operating modes: fixed frequency (with no sweep), manual
sweep, white noise, a slow single sweep lasting about 45 seconds (adjustable)
intended for recording onto tape for subsequent replay and analysis, and a
fast sweep lasting about 0.75 seconds intended for use with an oscilloscope
for direct analysis of a circuit or to show the effect of any tone controls
on your audio board.

The fixed frequency and noise modes produce a continuous output, with the
noise actually being a sound lasting about 1.3 seconds that is repeated
indefinitely, giving the impression of continuous noise.  White noise has a
uniform distribution of energy across the frequency range.

In the slow sweep mode, there is an option to momentarily mute the output
around half-octave boundaries (e.g. from 255 to 257 Hz) so that you can
determine the approximate frequency of any peak or trough without having to
continually monitor the display.  The frequency of the last marker is noted.

If you register the Audio Tools, you get access to a looped slow-sweep and
a pink noise facility.

In the fast sweep mode, there is a choice between a continuous or stepped
change of frequency, the steps allowing easier discrimination on the 'scope.
There is a 3:1 duty cycle to allow the 'scope to retrace and retrigger.  To
make the sound audibly better, the click caused by the suddent start and stop
of the sound can be virtually eliminated by turning on the Declick check box
(next to the fast sweep mode radio buttons).

In both sweep modes, the sweep may be linear or logarithmic in frequency, with
log being more suitable for examining a broad frequency response and linear
more suitable for narrow band filters.

In manual sweep mode there are two methods to alter the frequency.

  Method 1.  Ensure that the Stop/Start button has the focus, and then use the
Page Down and Page Up keys to control the direction and activation of the
sweep.  Because of the double-buffering used to keep the sound card busy,
there will be a slight delay between releasing either key and the sweep
stopping.  Starting and stopping the generator with the Start/Stop button
will ensure that it has the focus.  This method suits someone who wishes to
hold down a key for continuous, smooth frequency change.

  Method 2.  Ensure the trackbar (slider-like control) has the focus.  You can
then either drag the slider, or use the Page Down/Page Up, or Down Arrow and
Up Arrow keys to change frequency.  This method is quicker if you wish to
manually sweep a frequncy range looking for resonances.  Because the TrackBar
control can queue up several key presses to process at one time, you must
"peck" at the keys for each change of frequency rather than holding them down
continuously.

With method 2, you can also uncheck the "Lock L + R frequencies" checkbox to
obtain independent frequency control for left and right channels.


Frequency ranges:

You can program any frequency range you want into Sweep, but if you make the
maximum less than the minimum, you'll only get one frequency!  There is no
check against programming a frequency in excess of 22.05KHz, so you can
observe the effects of aliasing.

  For convenience, there are four preset frequency ranges called:

      wide:   20Hz .. 20KHz        hf:   1KHz .. 15KHz
    speech:  300Hz .. 3KHz         lf:   50Hz .. 1KHz


Output levels:

SweepGen has a choice of fixed output levels selectable from 0dB to -26dB in
1dB steps.  There will be a brief delay between selecting a new output level
and the actual output changing since, the internal sinewave lookup table has
to be recomputed, the output buffers refilled, and sent to the Wave device.
There is also a deliberate delay to avoid many quick changes being processed
since this is aurally rather distracting.


Output phase:

There are three modes of output operation.  Normally, both left and right
channels are indentical, i.e. in-phase.  Optionally, you can make the channels
out-of-phase which can be useful for checking the relative phase of a pair of
loudspeakers.  If the two speakers are out of phase, there will be less low-
frequency output.  The channels option allows you to hear this effect
directly.  The third output mode provides for independent control of channel
amplitude.  The program does not provide a mono-summed mode where two different
frequencies at different amplitudes are fed equally to each channel.


Release History:

Release V3.7.6.38
V3.7.6  2015-Aug-10  Greater output attenuation range
                     Change default level to -20 dB


(Earlier release notes are in the file History.txt}


Notes:

The program is written for Embarcadero Delphi.  You WILL need sound hardware
on your PC capable of full CD sampling rate operation (i.e. 16-bit, stereo,
44.1KHz - such as SoundBlaster 16 or later).  If SweepGen cannot open that
audio format it will complain.  I have seen some cards sold as 16-bit that
only actually offer 12-bit performance....

To measure your sound card itself, you may also find it helpful to have a CD
with a white-noise or frequency sweep source.  Two I have discovered are:

  Denon, Audio Technical CD 38C39-7147, 1984-5
  (includes white noise, but perhaps not now available?)

  Soundcheck Productions, Sound Check Alan Parsons & Stephen Court, 1993
  available as RS number 245-376,  Soundcheck tel: UK +44 1753 833524
  (pink noise plus many other signals and test tracks)

You may also want a sound editing program that is rather more capable than the
Sound Recorder included with Windows.  David Johnston's Cool Edit is low cost
and includes some spectral analysis capability.  Contact sales@syntrillium.com
or see their Web site for a demo copy.  (No longer sold - taken over by Adobe).


Acknowledgements:

magyar@krusty.eaglequest.com suggested the markers and manual sweep mode
(name lost) suggested the track bar frequency control
Peter Barratt requested the special phase step mode, to help tinnitus suffers
Dave Baxter suggested the toneburst before sweep to help 'scope triggering
Chris Coleman requested the removal of clicks with low frequency sweeps
Goran Hjalmarsson (and others) suggested the dual-channel output
Brad Stowers (bstowers@pobox.com) provided the Version Info routine
Bryan Timms suggested the custom sweep range and duration


Reference:

A book that I have found invaluable on digital audio is:

  The Art of Digital Audio, 2nd edition, 1994
  John Watkinson
  Focal Press (an imprint of Butterworth-Heinemann Ltd)
  ISBN 0 240 51320 7


+-------------------------- SAFETY NOTICE ----------------------------+
| Playing a continuous tone at a high level can damage your amplifier,|
| speakers, or hearing.  Please exercise sensible precautions!        |
+---------------------------------------------------------------------+

Program Status & Distribution:

The basic version program is freeware and remains copyright of David J Taylor,
Edinburgh, 1994-2014.  Purchase of a licence allows extra facilities to be
used.  This program is provided "as is", without any support.  Whilst I
cannot promise to answer queries relating to the use of this program, I'd
welcome any comments or suggestions for improvements you may have.  Requests
for distribution must be referred to the author, but will usually be granted
if no commercial gain is involved.

If you register the Audio Tools, you will be entitled to a reasonable level
of support, and gain extra facilities.  Register the Audio Tools here:
  http://www.satsignal.eu/software/reg-audio-tools.html


Contacting the author:

Web site:  http://www.satsignal.eu
E-mail:    davidtaylor@writeme.com

2015-Aug-10
