==============================================================
License Agreement for Fuji Xerox PS Driver
==============================================================

1. PROPRIETARY RIGHTS: Title, ownership rights, and intellectual
   property rights in the SOFTWARE shall remain in Fuji Xerox and its
   third party suppliers.  You have no rights in the SOFTWARE except
   as expressly granted in accordance with this agreement.
   
2. LICENSE:  Under this agreement, you are granted a non-exclusive
   license to use the SOFTWARE for the purpose of using with
   compatible Fuji Xerox products in your country.  You are
   not permitted to (1) assign, sublicense, sell, rent, lease, convey,
   or transfer the SOFTWARE to any third party by any tangible media
   such as floppy disk, magnetic tape, or CD-ROM, (2) distribute the
   SOFTWARE on a network or by a telephone line available to the public
   or (3) alter, modify, decompile, disassemble, reverse engineer, or
   create derivative works based on the whole or any part of the SOFTWARE.
   If any direction on usage or restriction for the SOFTWARE is
   expressly specified in this web site, you are required to follow
   such direction.
   
3. TERM: This agreement is effective upon installing the SOFTWARE
   until you terminate the agreement by destroying the SOFTWARE.
   This agreement will also terminate if you fail to abide by any
   terms of this agreement.  In case of termination, you must
   promptly destroy the SOFTWARE.
   
4. LIMITED WARRANTIES: THE SOFTWARE IS SUPPLIED STRICTLY ON AN 'AS IS'
   BASIS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR
   FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE SOFTWARE.
   YOU ARE RESPONSIBLE FOR CHOOSING, MAINTAINING AND MATCHING OTHER
   HARDWARE AND SOFTWARE COMPONENTS IN COMBINATION OF THE SOFTWARE.
   IN NO EVENT, SHALL FUJI XEROX, FUJI XEROX CHANNEL PARTNERS,
   AUTHORIZED DEALERS AND THEIR THIRD PARTY SUPPLIERS BE LIABLE FOR
   ANY LOSS OR DAMAGE INCLUDING INCIDENTAL OR CONSEQUENTIAL LOSS OR
   DAMAGE, ARISING FROM USE OF OR INABILITY TO USE SOFTWARE, OR ANY
   MODIFICATION OF THE SOFTWARE.  
   
5. EXPORT CONTROL: You are not allowed to export the SOFTWARE in part
   or whole, directly or indirectly, in violation of any restrictions,
   laws or regulations imposed by the government of your country or
   any other relevant countries, and are required to obtain necessary
   approval prior to exporting the SOFTWARE.


=======================================================================

FUJI XEROX DocuCentre/ApeosPort Series
Fuji Xerox PostScript(R) Driver (PPD file + INF file) for 
Microsoft(R) Windows(R) XP Professional x64 Edition,
Microsoft(R) Windows Server(R) 2003 x64 Editions,
Microsoft(R) Windows Vista(R) x64 Editions,
Microsoft(R) Windows Server(R) 2008 x64 Editions,
Microsoft(R) Windows(R) 7 x64 Editions and
Microsoft(R) Windows Server(R) 2008 R2 x64 Editions.

Supplemental Information
November 2009
=======================================================================

This document provides information about the PostScript(R) printer driver
on the following items:
1. Requirements
2. Models
3. Installation
4. Cautions and Limitations
5. Software Update

---------------------------------
1. Requirements
---------------------------------
Please note that this PostScript(R) Driver operates on a computer running on 
the following operating system. 
  Microsoft(R) Windows(R) XP Professional x64 Edition,
  Microsoft(R) Windows Server(R) 2003 x64 Editions,
  Microsoft(R) Windows Vista(R) x64 Editions,
  Microsoft(R) Windows Server(R) 2008 x64 Editions,
  Microsoft(R) Windows(R) 7 x64 Editions and
  Microsoft(R) Windows Server(R) 2008 R2 x64 Editions.

-----------------------------
2. Models
-----------------------------
The model names corresponding to this driver and the model names 
displayed during installation are shown below.  

Model Name                     : Model names displayed during installation
FX ApeosPort C7550 I PS        : FX AP C7550 I PS
FX ApeosPort C6550 I PS        : FX AP C6550 I PS
FX ApeosPort C5540 I PS        : FX AP C5540 I PS
FX DocuCentre C7550 I PS       : FX DC C7550 I PS
FX DocuCentre C6550 I PS       : FX DC C6550 I PS
FX DocuCentre C5540 I PS       : FX DC C5540 I PS

-----------------------------
3. Installation
-----------------------------
This section uses Microsoft(R) PostScript(R) Printer Driver, which is supplied 
as a standard component together with the following operating systems, to 
describe how to install a driver to use the target hardware product.  
  Microsoft(R) Windows(R) XP Professional x64 Edition,
  Microsoft(R) Windows Server(R) 2003 x64 Editions,
  Microsoft(R) Windows Vista(R) x64 Editions,
  Microsoft(R) Windows Server(R) 2008 x64 Editions,
  Microsoft(R) Windows(R) 7 x64 Editions and
  Microsoft(R) Windows Server(R) 2008 R2 x64 Editions.

To install the following models with Finisher Tray A or Booklet Stapling
Finisher Tray A installed, select the printer name with a suffix of "A" in
"Printer Name for Installation".
   * DocuCentre-II C3000


**There are two types of printer drivers installation, which are described
  below;


<<Installing Using the Windows XP x64 or Windows Server 2003 x64>>

 1) Click the "Start" button.  Point to "Printers and Faxes".   
    The "Printers and Faxes" folder opens.  Select "Install a printer" 
    (when Windows XP) or "Add a printer" (when Windows Server 2003).   

 2) In the "Add Printer Wizard", click "Next".

 3) Specify the printer connection.  When printer is directly connected  
    or when it is connected through network by using LPR protocol, then select
    "Local printer attached to this computer". Confirm that the check box 
    "Automatically detect and install my Plug and Play printer" is set to OFF, 
    and then click "Next" to proceed to Step (5). When the printer is connected 
    through network, select "A network printer, or a printer attached to another
    computer" and then click "Next". 

 4) Specify the printer name.  Enter a printer name or URL directly or 
    select a printer to be connected from the list of shared printers. 
    After selection, proceed to Step (7).
    (Contact the network administrator if you have any queries.)

    <Caution> Printing by entering URL is available only in IPP-supported models.

 5) When the printer is connected directly, select the port connected to 
    this product and click "Next".  Proceed to Step (7).
    When connecting directly to the printer through network using LPR 
    protocol, select "Standard TCP/IP Port" from "Create a new port" and 
    click "Next".
    "Add Standard TCP/IP Printer Port Wizard" is activated. Click "Next(N)".

 6) Enter the IP address for the printer into "Printer Name or IP Address", 
    on the TCP/IP Printer Port Wizard and then click "Next".
    (Contact the network administrator if you do not know the IP address.)
    Click "Finish".

 7) Select a printer model.  Click "Have Disk(H)" to display the "Install 
    from Disk" dialog box.

 8) Specify the folder containing this file "readme.txt" and click "OK". 
    * When installing from a CD-ROM, enter "F:\English\WinX64\.
      In this example, F drive is used as the CD-ROM drive. 
      If you are using another drive for CD-ROMs, specify accordingly.


 9) From the list of printers displayed, select the printer you are using 
    and click "Next(N)".

 10) Change the printer name, if necessary.  The message asking whether to 
     use this printer as the default printer is shown.  Make a selection and 
     then click "Next(N)". 

 11) If you share this printer with other network users, select "Shared(S)", 
     enter the required information, and then click "Next(N)". 
     If not, select "Not shared(O)" and click "Next".

 12) Specify whether to print the test page after installation.  If you 
     want to print, select "Yes".  If not, select "No".  Click "Finish".

 13) The dialog opens asking if you want to continue installation.  
     At this time, the message appears stating that you have not passed
     the Windows logo test; 
     however, you can continue the installation without any problem. Click 
     "Continue".

 14) Follow the instruction on the screen to continue the installation.

 15) After the necessary files are copied, the installation is completed.  
     Confirm in the "Printers and Faxes" folder that the printer is added. 

<<Installation on Windows Vista, Windows Server 2008 or Windows 7>>
 1) Click "Start" button, go to "Control Panel" and then "Hardware and Sound".
    Select "Printers" and click "Add a printer" command button.
    In the case of using Windows 7, click the [Start] button and select menu 
    in the following order.
    [Start] button  >  [Devices and Printers]
    Select [Add a Printer] in [Devices and Printers].

 2) Select status of printer connection. To connect printer directly or through
    networks using LPR protocol, select "Add a local printer". Go to Step (4).
    To connect printer through networks, select "Add a network, wireless or 
    Bluetooth printer".

 3) Specify printer. Select printer or click "The printer that I want isn't
    listed" and enter the name of the printer to install in "Select a shared
    printer by name". Go to Step (6).
    (Contact your Network administrator for any questions.)

    <Note> With the models other than IPP compliant, you cannot print
    documents by entering URL.

 4) If the printer is connected directly, select the port this product is
    connected to and click "Next". Go to Step (6).
    To connect the printer directly through networks using LPR protocol,
    select "Standard TCP/IP Port" from "Create a new port" and click "Next".

 5) Enter printer IP address. Enter the IP address in "Hostname or IP
    address" and click "Next".
    (If you do not know the IP address, ask your Network administrator.)

 6) Select printer model. By clicking "Have Disk...", "Install From Disk"
    dialog box is displayed.

 7) Click "Browse..." and specify the folder, in which this file (readme.txt)
    exists. Click "OK".
    * To install with CD-ROM, enter "F:\English\WinX64".  F: is mentioned as a
      CD-ROM drive here. If other drive is used, specify the name of the drive,
      to which you set the CD-ROM.

 8) Select the name of the printer model you use from the list displayed and
    click "Next".

 9) A dialog box to specify printer name is displayed. To change the printer
    name, enter the printer name in "Printer name" box. A check box will be
    displayed under "Printer name" box. If you specify the printer as a default
    printer, check on the box.

 10) Installation will start. "User Account Control Continue" dialog box will
     be displayed in the middle of installation. If you are asked whether to
     continue the installation, click "Continue".
     Depending on User's right, with which you logged in this time,
     Administrator name and password may be required.
     If so, enter the name and password.

 11) Depending on the models, a message, "Windows can't verify the publisher of
     this driver software" may be displayed but that is not a problem in function.
     Select "Install this driver software anyway" and continue the installation.
     * In the case of using Windows 7, the message, "Windows can't verify the 
       publisher of this driver software] will be displayed.

 12) By clicking "Finish", the driver installation is completed. Confirm that
     the printer is added in "Printer" folder. To output a test page before
     "Finish", click "Print a test page" button.
     To share the printer, open Property of the installed printer and change the
     settings on "Sharing" Tab.
     In the case of using Windows 7, if any other printer has been already installed, 
     the "Set as default printer" check box will be displayed. 
     To set the default printer, check the box and click the "Close" button.

<<Uninstallation of the Driver(for Windows Vista, Windows Server 2008 or Windows 7)>>

To uninstall the driver on Windows Vista(R),Windows Server2008 or Windows 7 completely, 
follow the instructions below and remove the driver and the driver package.

 1) Click "Start" button and select "Printers" on "Hardware and Sound" in
    "Control Panel".
     In the case of using Windows 7, Click "Start" button and select "Printers" on 
    "Devices and Printers" in "Control Panel".

 2) Delete the Printer icon in "Printers" folder.

 3) Right-click on "Printers" folder, select "Server Properties..." from
    "Run as administrator" and display "Print Server Properties".

 4) Select the driver to be removed on "Drivers" Tab and click "Remove..."
    button.

 5) Select "Remove driver and driver package." and click "OK" button.

 6) Reboot the computer.


------------------------------
4. Cautions and Limitations
------------------------------
<<Notes on Windows(R) 7>>

Driver installation method by Plug & Play (For Windows 7 users)
===============================================================
In the case of using Windows 7, driver installation by Plug & Play may not 
complete properly.
In such case, install the driver again following the process below.

- Click the "Start" button and select "Devices and Printers".
- Right-click on the icon of this printer in the [Devices and Printers] folder and click
  "Properties".
  * The icon may be uncontrollable with grayout.  Turn on the power of printer again 
    and be sure that the printer is connected by cable.
- In a condition of keeping this printer selected in "Device Functions" on the 
  "Hard ware" tab, click the "Properties" button and open the Property dialog.
- Click the "Change Settings" button and open new "Properties" dialog.
- Open the "Driver" tab in the new "Properties" dialog, click the "Update Driver" button 
  and open the "Update Driver Software" dialog.
- Select "Browse my computer for driver software" and specify the driver location 
  by "Search for driver software in this location",  Click the "Next" button.
  * As to how to prepare drivers, refer to the section, g**Using [Add Printer] to install".
- A message indicating that the driver has been updated will be displayed. 
  Close the dialog by clicking the "Close" button.  
  This is the end of the reinstallation.

Limitations concerning the page-by-sheet function
==================================================
Sometimes, if Page-by-Sheet, 2-Sided Print, and Collate are 
specified concurrently, only borders will be printed on side 2.  As 
this behavior is a result of Windows OS specification, prevention 
is not available.  When this happened, the side 2 that contains 
only borders will be counted as part of the print data. 

Limitations concerning the use of shared printer
================================================
When sharing a printer, this driver must be running on the target 
OS on the server as well as the client.  
You cannot produce alternative driver for 32-bit Windows OS using 
this driver.  Please refer to "1. Prerequisites" regarding the 
target OS for this driver.  


Limitations concerning plug-ins for additional functions
========================================================
This driver does not provide plug-ins for additional functions.  As 
a result, some functions provided by 32-bit Windows OS drivers 
cannot be used.  The following are the main functions that cannot 
be used.  

    - Secured Print
    - Sample Print
    - Delayed Print
    - E-mail Job Confirmation 
    - Banner Sheet
    - Image Rotation (180deg)
    - Account Management functions
    - Get Information from Printer


<<Limitations of MS PScript 5>>

Printing with Collated
======================
When "Internal Hard Disk" is set to "Installed" in "Device Settings" and the 
MS PScript 5 driver is used to do a collate printing from Microsoft Word 
97/98/2000, select the "Collated" check box on the print dialog in Microsoft
Word 97/98/2000.

Negative Output
===============
When 2-up or 6-up printing in a negative image output is specified for a 
portrait document, a print job may not be performed properly.
*Negative Output is not supported for color machines.

Image Rotation 180 Degrees
==========================
When margin is specified on the server property and "Image Rotation 180 Degrees"
is specified to do a print job, printing position in the print output is 
different from the desired one. 

Limitation of PostScript Output Format (1)
==========================================
When PostScript Output Format is set to "Optimize for Portability", 
if Multiple-UP is set to 2 Up or 6 Up, the print job may not be output normally.

Limitation of PostScript Output Format (2)
==========================================
When PostScript Output Format is set to "Encapsulated PostScript", the settings 
for printing such as paper source, output method, number of copies, pages to be 
output etc. will be invalid.
Please do not use "Encapsulated PostScript" when printing.

Limitation of PostScript Output Format (3)
==========================================
When PostScript Output Format is set to "Archive format", the print job may not 
be output normally.
Please use "Archive format" when outputting as a file only.




Application-Specific Limitations
================================
The feature to correct the orientation of a Custom Paper Size is not available
in some applications, such as Acrobat. 

Range for Custom Paper Size
===========================
The range of Custom Paper Size that is available for PostScript driver may be 
different depending on the models. The paper size exceeding the range of Custom 
Paper Size (including slight errors due to unit conversions) may not be printed 
properly.

Paper Size
==========
When an application allowing for Paper Size specification such as Microsoft Word
is used, specify the same Paper Size in the application and the driver.


Choukei 3 Paper Size
====================
When printing multiple Copies with Paper Size specified as Coukei 3, 
a message may appear on a printer stating that Paper Size is incorrect.  
In such case, stop printing and specify Heavyweight 2 for Paper Type 
(Bypass Tray) to do a print job.
 

Limitations to Windows Server 2003
==================================
To upgrade Windows 2000 Server to Windows Server 2003, uninstall the 
pre-installed driver before upgrading to Windows Server 2003.  
Then, in the upgraded Windows Server 2003, install the upgraded driver.

From To Tray Assignment on Device Settings Tab
=================================================
When From To Tray Assignment is specified, the Auto feature of Paper Source is 
disabled, and the Substitute Tray feature may be disabled, too. To avoid this, 
set TrayN to Not Available.

N-Up
====
When printing a document consisting of an odd number of pages, closing lines
may be printed on the page that should be blank.  
To avoid this, uncheck the Enable advanced printing features check box on the 
Detailed Settings tab before printing.



<<Limitations about MS PScript 5 driver for Windows Vista(R)>>

Installation through networks
=============================
In the case of installation through networks, if you right-click on "Printers",
go to "Run as administrator" and select "Add printer..." to perform installation,
printer icon may not be generated. In such case, select "Add printer..."
command button.

Limitations on shared printer
=============================
If the driver is shared through networks and another driver of different
architecture is specified to install, a dialog asking you for media for the
specified architecture will appear.  After the setting, however, the dialog
reappears and installation cannot be performed.
For example, additional installation of x64 driver on x86 OS corresponds to
this case.


Limitations of font
===================
Depending on a combination of your application software and fort in use,
the characters may be garbled.
In such case, the problem may be resolved by changing the settings of
"True Type Font Download Method" to "Outline" or "Bitmap".


<<Notes on Windows Server(R) 2008>>

Installation in Windows' cluster environment
============================================
To install the driver in the restricted cluster environment, you have to 
install the driver for each node first.  

Limitations on remote installation
==================================
When remote installation is executed for Windows Vista or later operating 
system, driver installation may not end properly.  In this case, please 
perform remote installation from Windows XP.  

Limitations on shared printer
=============================
When the driver is shared over the network and the driver, with different 
architecture, is specified and installed as an additional driver, a 
dialog box requesting for the specified architecture media will appear.  
Even if you have made an entry in the dialog box, it will keep on 
appearing, causing the installation to fail.  
For example, this will happen when installing x64 driver on x86 operating 
system.  



<<Notices and Restrictions for the use of Windows Sever 2003 on Cluster Server>>
Please use the following operating systems as client.  
  Microsoft(R) Windows(R) 2000
  Microsoft(R) Windows(R) XP
  Microsoft(R) Windows Server(R) 2003
  Microsoft(R) Windows Server(R) 2008
  Microsoft(R) Windows Vista(R) 
  Microsoft(R) Windows(R) 7 

Restrictions on getting printer information and viewing the printer status
When Windows 2000 Server or Windows Server 2003 is used in cluster server 
environment, [Get Information from Printer] and [Status] features do not operate
normally on virtual server. Also, when the driver installed from a cluster 
server through the network is used, [Get Information from Printer] and [Status]
features do not operate normally.

To get printer information, click [Get Information from Printer] button and then
enter IP address of your printer. Likewise, to view the printer status, click
[Status] button and then enter IP address of your printer.


<<Limitations to Available Features >>

Limitations to Print As Gray and Print Pattern
==============================================
If moire occurs when printing with Print As Gray or Print Pattern specified, 
it may be avoided by changing the setting of Halftone Print or Print Mode. 

Enlargement
===========
When enlargement over 200% is specified, lines and figures may not be 
printed properly in some applications. 

Limitations for printing in black and white using the color models
==================================================================
Depending on the OS or the application software you are using, even if 
the display image is in black and white, the output may be in color 
being processed with process black (using full-CMYK).
To ensure that the output is in black and white mode, set [Output Color] to 
[Black] for printing.

ICC profiles
============
While Windows(R) 2000 supports ICM 2.0, your installing the driver cannot make
ICC profile associated with the printer.
Go to [Color Management] tab and make an appropriate ICC profile associated
with the printer manually.


<<Limitations to Collate Printing>>

Device Setting
==============
When "Internal Hard Disk" is set to "Not installed" in "Device Settings" of the 
printer driver, collate printing is not available even though the hard disk is 
installed actually. When the internal hard disk is installed to the printer, 
set "Internal Hard Disk" to "Installed" in "Device Settings".

Application-Specific Limitations
================================
Collate printing is not available in some applications, such as Acrobat 3.0 for 
Windows. Collate printing for mixed-size document is not available in some 
applications, such as Microsoft Word 97/98/2000 for Windows.


<<Limitations to Paper Source>>

Paper Source Setting
====================
When Paper Size is specified as Postcard, Pre-Paid Postcard, SRA3, or 5.5x8.5", 
paper can be fed only from the bypass tray. If Paper Source is set to "Auto", 
a print job may not be performed properly. When printing on paper of these paper
sizes, set Paper Source to the "Bypass Tray".


<<Printing in Inverse Order>>

Application-Specific Limitations
================================
In some applications, such as Acrobat, PageMaker, CorelDraw, and QuarkXPress, 
printing in an inverse order may not be performed properly.


<<Limitations to Margin>>

Margins for Landscape Document
================================
When "Image Orientation" is set to "Landscape", settings for top/bottom 
margins and for right/left margins may be performed inversely, respectively.
This issue can be avoided by setting "Image Orientation" to "Landscape
Rotation" or exchanging the values between top and bottom, between right and 
left for the margins to be set.

Application-Specific Limitations
================================
Margin setting is not available in some applications. 

Limitations concerning 2-Sided Printing
=======================================
If you are using 2 Sided Print to print documents with odd-number of pages, a 
blank page may be added to the last page depending on the settings of the 
operating system (referred to as "OS" hereinafter). 
If you are using Windows 2000/XP or Windows Server 2003 or Windows Vista, 
display the Properties dialog box from the printer icon and deselect the 
[Enable advanced printing features] in the [Advanced] tab.
This will prevent the printer from adding blank paper to the printout. 
However, please take note that once this check box is unchecked, 
Reverse Printing and Booklet Printing will become unavailable. 
In addition, some application software will automatically insert blank sheet 
for page adjustment according to the condition for specifying print quantities 
regardless of the OS type. 
As this behavior is a specification of the application software, it is not 
possible to configure this driver or the device to prevent blank sheet from 
being inserted to the printout.  The target device will print the data as per 
received after being edited and printed from the client's side according to the 
OS or application software specification. 
If the document data to be printed consist of blank-sheet data inserted by the 
OS or application software, this blank sheet will be counted as part of the 
print data. 


<<Limitation to Gradation>>
With the application such as Microsoft PowerPoint 2001, smooth gradation may not 
be obtained in the background of a printed image, etc. In such case, change the 
Resolution or the Halftone setting and try printing. 


<<Limitations to Specific Applications>>

Adobe PageMaker(1)
==================
When using Adobe PageMaker 6.5/7.0, TrueType font may not be printed properly.  
To avoid this, select "Print" while pressing the "Alt" key.

When using the auto tiling feature of Adobe PageMaker 6.5/7.0, a partial mage 
loss may occur. 

Adobe PageMaker(2)
==================
With Adobe PageMaker, when this printer is specified for "Compose to printer", 
a layout may change in printing. This issue can be avoided by performing the 
following steps;
1) Do not set "Compose to printer".
2) Change the "Margin" setting in advance in the printer folder.
3) Specify "Extended" on the Print Area tab in advance in the printer folder.

Adobe PageMaker(3)
==================
When printing a document with multiple images pasted, some images may be 
shifted a little in printing.

Adobe PageMaker(4)
==================
When using Adobe PageMaker, if you enlarge or reduce the image from the driver 
side, the output image may be out of the alignment. To avoid this, enlarge or 
reduce it from PageMaker side. 

Adobe Illustrator(1)
=====================
When a bitmap font of an European font is output, a PostScript error may occur.  
To avoid this, install the applicable outline font file.

Adobe Illustrator(2)
=====================
When 2 Sided Print or N-up is specified to do a print job, 
the desired print results may not be obtained.


DocuWorks Viewer Light
======================
Driver-specified Paper Size is not reflected.  
Paper Size in a DocuWorks document is given priority.

CorelDRAW(1)
============
When printing with CorelDraw, curving line or slanting line may not be printed 
smoothly. In such case, deselect the "Use PPD" check box and try printing.

CorelDRAW(2)
============
When printing with CorelDRAW, the Collated feature may not be enabled . 
This issue can be avoided by deselecting the "Use PPD" check box.

CorelDRAW(3)
============
When using CorelDRAW, the output image may rotate by 90 degrees.  
In such case, check [Use PPD] in [General] tab in Print dialog of CorelDRAW 
and select PPD file for the model you are using.  
PPD files are installed in the following folder.
<System Folder>\system32\spool\drivers\x64\3

The PPD files corresponding to the each printer name are as follows.
FX ApeosPort C7550 I PS     FXA75EE2.PPD
FX ApeosPort C6550 I PS     FXA65EE2.PPD
FX ApeosPort C5540 I PS     FXA55EE2.PPD
FX DocuCentre C7550 I PS    FXD75EE2.PPD
FX DocuCentre C6550 I PS    FXD65EE2.PPD
FX DocuCentre C5540 I PS    FXD55EE2.PPD


Lotus Freelance
===============
When using Lotus Freelance, grouped figures may not be printed properly.

Microsoft Word
==============
When printing from Microsoft Word, translucent figure and characters may 
not be printed properly. 

Microsoft Word 2000
===================
The setting of Other pages, of which setting dialog opens by selecting 
[Page Setting]->[Paper Tray], may not be enabled.

Microsoft Word 2002/2003
========================
The setting of Other pages, of which setting dialog opens by selecting 
[Page Setting]->[Paper], may not be enabled.

Microsoft Word 2002(1)
======================
When doing a print job by specifying N-up (2 up or more) over IPP/SMB connection
with Microsoft Word 2002, printing is executed without the N-up feature.   
If you desire to print with the N-up feature, do a print job over another 
connection, such as lpr.

Microsoft Word 2002(2)
======================
If Booklet Printing is performed on Microsoft Word 2002, the layout on the 
output may be distorted.


Microsoft Word 2007
===================
When performing 2 Sided Print for documents with an odd number of pages on 
Microsoft(R) Office Word2007, the application software may insert blank separators 
automatically to adjust pages.  In that case, the blank separators output are 
counted up for billing.
If you use a driver model with the feature of "Skip Blank Pages" in 
Printer Properties display, you can avoid outputting blank separators by checking 
"Skip Blank Pages" on "Advanced" Tab in "Printing Preferences" dialog or
setting it "on" with the printer/multifunctional device.


Microsoft Word for Windows
==========================
When printing the data using Section Break from Microsoft Word for Windows, 
N-up printing may not performed properly.  This issue can be avoided by 
using Page Break instead of Section Break.

Windows Microsoft Word 97/98/2000
==================================
When "Bypass Tray" is specified for Paper Source, the printing may be 
interrupted with the message "Load Paper XX" (XX: paper name) appearing on the 
UI panel of the printer. In such case, temporarily load the paper required for 
paper trays 1 through 4.

Microsoft Excel
===============
When printing an entire book from Microsoft Excel, the desired print results
may not be obtained.

Objects may not be printed correctly with Microsoft Excel.  
In such case, change the Resolution setting and try printing.

The feature of [Multiple-UP] or [Pages Per Sheet] may not function on Microsoft 
Excel. In that case, the problem may be resolved by changing the paper size 
settings to the same size with another name on Microsoft Excel. For example, 
change the settings of A4 to A4 (210 x 297mm) or B5 to B5 (182 x 257mm).


Microsoft PowerPoint
====================
When printing a GIF image, the area surrounding the image may not be made 
transparent in printing.

Microsoft Internet Explorer
===========================
When printing with Internet Explorer 6.0, the Sample Set feature is not available.

Adobe Acrobat(1)
================
The feature of [Mirror Image] may not function normally.
In that case, open [Print] dialog box on Acrobat and put a check to 
[Print as image].

Adobe Acrobat(2)
================
When printing an Acrobat document, the Page order feature of the driver may not 
be performed. This issue can be avoided by selecting "Reverse pages" check box 
on the Print dialog of Acrobat.

Adobe Acrobat(3)
================
When printing from Adobe Acrobat with "Use Printer Font" set to ON, the desired
print results may not be obtained.  In such case, set "Use Printer Font" to OFF 
for printing, so that "Landscape Rotation by 180deg" setting is not reflected on
print results. 

Adobe Acrobat 5.0
=================
If [Choose Output Tray by PDF page size] in [Print] dialog box is set to ON, 
the print job may not be performed properly.  In such case, change the settings 
to OFF.

Adobe Acrobat 6.0
=================
If [Choose Paper Source by PDF page size] in [Print] dialog box is set to ON, 
the print job may not be performed properly.  In such case, change the settings 
to OFF.

Adobe Acrobat 6.0/7.0
=====================
If [ImageRotation] feature is used, the image may not be output normally.  
In such case, check [print as image] in [Print] dialog box of Acrobat.

Adobe Acrobat 7.0
=================
When using Adobe Acrobat of the version 7.0.0 or later and any previous to 7.0.5, 
if you specify multiple copies for printing, Stapling and Offset may not 
function properly. The issue can be resolved by updating Acrobat to 7.0.5.

Adobe Acrobat7.x/8.x
====================
If [Choose Paper Source by PDF page size] in [Print] dialog box is set ON,
2 Sided Print may not be output correctly.
In such case, check [print as image] in [Print] dialog box of Acrobat.

Adobe Acrobat8.x
================
When [Secure Print] or [Sample Set] is specified, Document Name may not be 
displayed correctly on the main panel.

Macromedia FreeHand
===================
FreeHand do not support N-up, Scaling, Mirror Image.


<<LPR Connection>>
When the dialog "Further information about the port is required." is displayed 
in the "Add Standard TCP/IP Printer Port Wizard", select a supported printer in 
"Standard" of "Device Type".


<<Standard TCP/IP Port>>
In some applications, a document may not be printed. In such case, 
try to select LPR Byte Counting Enabled of Configure Standard TCP/IP Port 
Monitor.


<<Printing A Blank Page by Error When N-UP is Specified>>
A blank page may be printed out under the following conditions:
When "Detailed Print Features" is set to ON, "Internal Hard Disk" is set to 
"Not installed", 
"Collated per set" check box is selected, and N-up is specified.

------------------------------
5. Software Update
------------------------------
    The latest software is available on our web site.

        http://www.fxap.com.sg/default.jsp

    Communication charges will be borne by the customer.


--------------------------------------------------------------------------------
Adobe, Acrobat, AdobePS, ATM, PageMaker, PostScript, Adobe Type Manager, 
Adobe Illustrator, Adobe Photoshop are trademarks of Adobe Systems Incorporated.

Microsoft, Windows, Windows Server, and Windows Vista are 
registered trademarks or trademarks of Microsoft Corporation in the United 
States and other countries.

Other product names and companies names are the registered trademarks or 
trademarks of their respective owners.

(C) Fuji Xerox Co., Ltd. 1999-2009
